Novel TiC-based composites with enhanced mechanical properties

Novel TiC-based composites were synthesized by reactive hot-pressing at 1800 °C for 1 h with ZrB₂ addition as a sintering aid for the first time. The effects of ZrB₂ contents on the phase composition, microstructure evolution, and mechanical properties were reported. Based on the reaction and solid solution coupling effects between ZrB₂ and TiC, the product ZrC may be partially or completely dissolved into the TiC matrix, and then phase separation within the miscibility gap is observed to form lamellar nanostructured ZrC-rich (Zr, Ti)C. The TiC-10 mol.% ZrB₂ (starting batch composition) exhibits good comprehensive mechanical properties of hardness 27.7 ± 1.3 GPa, flexural strength 659 ± 48 MPa, and fracture toughness of 6.5 ± 0.6 MPa m^1/2, respectively, which reach or exceed most TiC-based composites using ceramics as sintering aids in the previous reports.     

An Image Super-Resolution Reconstruction Method with Single Frame Character Based on Wavelet Neural Network in Internet of Things

Mobile Networks and Applications - The application of the traditional single frame character image super-resolution reconstruction method has some problems, such as noise can not be removed...     

The influence of brewing method on bioactive compounds residues in spent coffee grounds of different roasting degree and geographical origin

The content of bioactive compounds in spent coffee grounds (SGC) was studied. SGC were obtained from Coffea arabica beans of different roasting degrees (light and dark) and different geographical origins (Nicaragua, Columbia and Mexico) processed using four brewing methods (mocha, filtered, drip and infusion). The highest caffeine and chlorogenic acid contents were determined in filtered spent coffee extracts. All extracts of light roasted spent coffee grounds showed lower browning index levels in comparison to that from dark roasted spent coffee grounds. Generally, the highest content of total polyphenolic compounds and highest antioxidant capacity were determined in extracts prepared in drip. In conclusion, the results obtained in this study indicate that the spent coffee grounds produced of domestic levels, especially those obtained from filter coffeemaker, could be considered as a good source of natural antioxidants.     

Torsional statics of two-dimensionally functionally graded microtubes

A size-dependent governing equation is derived to investigate the torsional static behaviors of two-dimensionally functionally graded microtubes based on the modified couple stress theory. The shear modulus is assumed to vary along the tube’s length direction according to an exponential distribute function, and varies along the tube’s radius direction according to a power-law function. A generalized differential quadrature method is developed to determine the rotational angle and shear stresses. Some illustrative examples are given to investigate the effects of applied torques, the length scale parameter and various material compositions on the torsional angle and shear stresses.     

Densification,mechanical and thermal properties of ZrC1 − x ceramics fabricated by two-step reactive hot pressing of ZrC and ZrH2 powders

Densification behavior, mechanical and thermal properties of ZrC_1 ? x ceramics with various C/Zr ratios of 0.6–1.0 have been investigated by two-step reactive hot pressing of ZrC and ZrH₂ powders at 30 MPa and 1500–2100 °C. The two-step reactive hot pressed ZrC_1 ? x ceramic has a higher relative density (> 95.3%) than that (91.9%) of stoichiometric ZrC sintered at 2100 °C. A cubic Zr₂C-type ordered phase forms in the ZrC_1 ? x sample obtained at a ZrC/ZrH₂ molar ratio of 0.6 at a relatively low temperature of 1100 °C. The decrease in C/Zr ratio is beneficial to densification of ZrC_1 ? x ceramic, however, excess grain growth occurs after sintering above densification temperature. The elastic modulus and Vickers hardness decrease with decreasing the C/Zr ratio. With decreasing the C/Zr ratio, both thermal conductivity and specific heat decrease due to the enhanced scattering of conducting phonons and electrons by carbon vacancies.     

智能卡车调度系统在紫金山露天矿的应用

紫金山露天矿采用多种开拓运输方式,设备大型化、机械化程度较高,但采矿生产过程存在机械设备作业范围大、作业面广、作业点多的特征,安全管理、生产管理形势严峻。本文立足紫金山生产模式,针对该矿智能卡车调度系统的建设,提出进一步完善卡调系统运行管理、提高露采数字化管控水平的措施,旨在充分发挥卡调系统对生产的智能辅助,提升露天采矿安全管理、生产管理、资源管理及成本管理水平,打造新时期智慧矿山建设新标杆。     

A Comparative Study of Mechanical Properties,Thermal Conductivity,Residual Stresses,and Wear Resistance of Aluminum-Alumina Composites Obtained by Squeeze Casting and Powder Metallurgy

Squeeze casting and powder metallurgy techniques were employed to fabricate AlSi12/Al₂O₃ composites, which are lightweight structural materials with potential applications in the automotive industry. The impact of the processing route on the material properties was studied. Comparative analyses were conducted for the Vickers hardness, flexural strength, fracture toughness, thermal conductivity, thermal residual stresses, and frictional wear. Our results show that the squeeze cast composite exhibits superior properties to those obtained using powder metallurgy.

     

Effect of boron addition on microstructure,mechanical properties and oxidation resistance of TaC ceramics

TaC ceramics with 0.03–0.60?wt% of boron additions were prepared by hot pressing at 2100?°C for 1?h under a pressure of 40?MPa. Effects of boron content on densification, phase composition, microstructure, mechanical properties and oxidation resistance of the TaC ceramics were investigated. When the boron content was 0.12?wt% and above, full density was obtained due to reactions between boron and oxygen impurity at presence of TaC. Minor phases of TaB₂ and C were formed in the 0.24 and 0.60?wt% B compositions after gas-out of the oxygen impurity. Microstructure of the TaC ceramics was refined with increasing in boron content. The TaC ceramic with 0.24?wt% of boron showed the best mechanical properties with a Vickers hardness, flexural strength and fracture toughness of 17.7?GPa, 534?MPa and 4.6?MPa?m^1/2, respectively. When more boron was added, interfacial bonding of the TaC grains was strengthened causing a decrease in fracture toughness. Oxidation resistance of the TaC ceramics increased with boron content. Particularly, the 0.60?wt% B composition showed a weight gain of 0.0018?g/cm² after oxidization at 800?°C in air for 3?h.     

Correction to: A Comparative Study of Mechanical Properties,Thermal Conductivity,Residual Stresses,and Wear Resistance of Aluminum-Alumina Composites Obtained by Squeeze Casting and Powder Metallurgy

Metallurgical and Materials Transactions A -